Composite Materials： Design and Applications (CRC 2003)

fenglianxiang

Composite Materials： Design and Applications (CRC 2003)
page：523
' v( I6 o, ~( ]# t7 b/ u
French editions published by Editions HermEs, Paris, 1997
No claim to original U.S. Government works
International Standard Book Number 1-58716-084-6
; K$ T- e! g. e1 L7 |% X+ ?! }Library of Congress Card Number 2002073794
简介
This book contains information obtained from authentic and highly regarded sources. Reprinted material is quoted with
permission, and sources are indicated. A wide variety of references are listed. Reasonable efforts have been made to publish
+ D" G. W: D/ qreliable data and information, but the author and the publisher cannot assume responsibility for the validity of all materials
or for the consequences of their use.
8 `' X) s7 h  ~; S8 Q' r1  Composite Materials, Interest, and Properties
' ~6 Z1 k1 a  J. D1.1  What Is Composite Material?
* H' K- x8 A3 e1 j! }$ D1.2  Fibers and Matrix
1.2.1  Fibers
: b$ B+ j: O& D1.2.2  Matrix Materials
2 ?5 }  i! j/ L8 g! Q  h( z1.3  What Can Be Made Using Composite Materials?
1.4  Typical Examples of Interest on the Use of Composite Materials
1.5  Examples on Replacing Conventional Solutions with Composites
) H% t6 w! T7 E" a9 b) H( l* D1.6  Principal Physical Properties
, ?. U3 b1 `8 [8 t/ }3 w5 K( L2  Fabrication Processes
3 `6 e: Z1 K8 w  i2.1  Molding Processes
2.1.1  Contact Molding
2.1.2  Compression Molding
- A" ~! Q: l# j* A" S2.1.3  Molding with Vacuum
2.1.4  Resin Injection Molding
: Z" J; D7 L) Q2.1.5  Molding by Injection of Premixed
9 }, g6 [6 q- e, c0 H6 L& A  ^2.1.6  Molding by Foam Injection
2.1.7  Molding of Components of Revolution
2.2  Other Forming Processes
2.2.1  Sheet Forming
2.2.2  Profile Forming
- C3 i& G* z( }( }3 ?2.2.3  Stamp Forming
2.2.4  Preforming by Three-Dimensional Assembly
8 J! i, S' p3 r5 V% p0 |2.2.5  Cutting of Fabric and Trimming of Laminates
2 \7 N0 Q: `; j) ?1 v. _9 N+ t+ y2.3  Practical Hints on Manufacturing Processes
9 T5 C2 f- u9 y+ _; ?8 o1 h2.3.1  Acronyms
2.3.2  Cost Comparison
0 L2 p1 G* I1 s! i3  Ply Properties
3.1  Isotropy and Anisotropy
# W  L  ?' Z( {2 m$ l3.1.1  Isotropic Materials
9 e. o1 g* I2 Y; b% n3.1.2  Anisotropic Material
3.2  Characteristics of the Reinforcement–Matrix Mixture
* Z& E4 \+ q- u  C7 k# j3.2.1  Fiber Mass Fraction
# l+ p5 P1 V: ^, \3.2.2  Fiber Volume Fraction
3.2.3  Mass Density of a Ply
3.2.4  Ply Thickness
...............
共9个压缩卷，解压后18.3M

[ 本帖最后由 fenglianxiang 于 2008-8-5 16:43 编辑 ]