8 J `) Z! L+ l" J: W0 ?
Sorry, You've got a bad luck ' o: u1 E% F! O+ O' T9 R# u; F9 R Win XPSP3 has a bag with reading intermediate toolpath results file in HSM 2.3.3.6892 .. So it can not build a toolpaths... + W* F% d: l+ i. P" G# E% S g6 l( M. A1 e0 Q
[ 本帖最后由 solid_user 于 2008-9-16 05:28 编辑 ]
# l, q8 w- I" m2 Q+ YI don't know.. If you have got a newer than HSM 2.3.3.6892 Installation for Mc9.1 I can try to make a crack. Maybe it will be work under Windows XP XP3 . w) ~- Y& D0 M0 ]4 Z$ O) ?: |. i m2 ]7 n6 ]# y
BTW HSM 3.0.31 for MC X-X3 is already released om cimco-hsm.com / _# f/ d& g3 V. S: [ 3 L& L8 t) [% K2 Z4 l' |- k[ 本帖最后由 solid_user 于 2008-9-16 05:49 编辑 ]
error: failed to read from kernel stream (please try to repair the installation) 1 C2 F, M B$ v3 c! V* U8 _error: toolpath generation failed 4 t6 ~; Y" J4 w2 a7 N* v! i1 h
' c* U7 B3 @9 v5 I( L1 T
I think I have to change the system
原帖由 joks 于 2008-9-16 06:11 发表 http://www.3dportal.cn/discuz/images/common/back.gif, Q* x9 E% n6 @9 ^) K
error: failed to read from kernel stream (please try to repair the installation)" f2 }! l7 x4 q; A# a6 b H
error: toolpath generation failed ; Z3 w* [2 j& J# g' K0 h8 r
& \# \! z; r6 m, C* u$ {$ S
I think I have to change the system
9 \2 C0 `3 `# b1 U- a, r% }: c
That's bug of Win XP SP3 I said...( N- E4 h5 k8 u$ r. o* C- h% Q6 S
In Win XP SP2 all works and you will not get that message " V5 m7 H' Q | @% A: q' {# f" f9 @
: \. L) t2 U1 F+ {" p7 }I use different OS's on different computers.. F% `% {3 w, C2 c
As for HSM 3.x.x it's good but it can not be run under MC 9.1... I think you need HSM not only for MC X-X3 but for MC 9.1 too.. Isn't it?6 d* e1 n# P2 {: R' k
1 p& ^2 W2 ] [8 Z# J
BTW MoldPlus v10 SP0 for Mastercam X3 is already released on mastercam.fi 1 q, ?! V- r5 @. |: K; [
I use different OS's on different computers.. = Oh!5 Q" v! O3 [ |" M# q& m6 i
8 t7 f; E/ T/ z: XAs for HSM 3.x.x it's but it can not be run under MC 9.1... I think you need HSM not only for MC X-X3 but for MC 9.1 too.. Isn't it? = Yes! I started learning is the most Mastercam, I like mastercam!7 \- J2 m! {0 Z1 W( L9 t" @
! j6 P- N" K# w* D
BTW MoldPlus v10 SP0 for Mastercam X3 is already released on mastercam.fi = Moldplus_10_SP0_for_X3 can use it without Crack ?
error: failed to read from kernel stream (please try to repair the installation)+ X- u" {. d6 L* ]- [
error: toolpath generation failed / G9 |# F) X3 B3 A
WORK IN SP2
原帖由 ryanhe2008 于 2008-9-17 10:56 发表 http://www.3dportal.cn/discuz/images/common/back.gif: a: `7 Z. U. {; Q" W9 f$ w
error: failed to read from kernel stream (please try to repair the installation)) L1 A2 l9 f( j! \: B# F2 c5 g* d5 J
error: toolpath generation failed . q5 W+ ^. |5 v8 nWORK IN SP2
6 [( c, h" h9 ^% _2 i" \
I suppose that you have install some of Windows XP2 Update wich couse this bug..( K2 i5 S$ P# N2 f& J, D' E
In any case it's bug of Windows..
发表于 2008-9-16 03:48:05
Sofa! Thank you very much
/ v a) g( G% [' K( J- Z
楼主
' o: u1 E% F! O+ O' T9 R# u; F9 R
" V5 m7 H' Q | @% A: q' {# f" f9 @
1 q, ?! V- r5 @. |: K; [
Oh!5 Q" v! O3 [ |" M# q& m6 i
Yes! I started learning is the most Mastercam, I like mastercam!7 \- J2 m! {0 Z1 W( L9 t" @
Moldplus_10_SP0_for_X3 can use it without Crack ?