|
|
发表于 2009-5-26 16:02:33
|
显示全部楼层
来自： 中国北京
Part.AddComponent "E:\毕业设计\新生成零件\连杆.SLDPRT", 0, 0, 01 o$ T2 @! o! h' \) |
这里的“Part”应该是个装配体，你把 'Set Part = swApp.NewAssembly给注销了，所以Part 是个零件图，当然没法插入零件了，我给改了改，仅供参考：
l% r) `7 t( e( ^7 `& J4 o4 q2 K2 @) P, _) a5 h1 I
Sub main()" u& ]2 m8 ^" t3 a7 {7 C* W
$ `# K, T J+ h: a Dim swApp As SldWorks.SldWorks. O) t9 }9 J+ i7 M2 E
Dim swAssy As SldWorks.AssemblyDoc
7 m1 F* e, `* p2 B Dim swPart As SldWorks.PartDoc% W+ D7 i# x5 o
Dim longstatus As Long5 v/ b6 s1 m8 m0 a
Dim longwarnings As Long
! z0 f$ L! L) C6 ~' M: C Dim sPartFileName As String, X* e. I( k, Z$ F4 Q/ y( e. W3 j
Dim Boolstatus As Boolean$ w: V; e& r. W" w/ H3 y Z o
- F) J# y+ N" Q- G ?
Set swApp = Application.SldWorks1 Q x6 ]* I/ r2 S5 y/ e8 l
Set swAssy = swApp.ActiveDoc7 }9 o7 @6 E" I
6 @& K6 q Q% i4 j6 d2 D6 D/ \ If (swAssy.GetType <> swDocASSEMBLY) Then Exit Sub '当前文档若不是装配体则退出
# F% _% @; o' K) Z# h' ]
* x$ @4 N+ W+ ?1 I1 E8 M sPartFileName = "E:\毕业设计\新生成零件\连杆.SLDPRT"# C$ \: J2 I4 g$ z
4 d& W' c) L7 T o swApp.DocumentVisible False, swDocPART
+ h( k2 K% h4 n8 y Set swPart = swApp.OpenDoc6(sPartFileName, swDocPART, 0, "", longstatus, longwarnings)' {2 z+ A" o' s! g- q/ i
- N3 `: }& a0 l$ C7 a6 O
If swPart Is Nothing Then swApp.DocumentVisible True, swDocPART: Exit Sub, K4 M0 D0 |9 R2 t3 @! t: g
& \: ^5 f- z0 h3 L: b( z, b
Boolstatus = swAssy.AddComponent(sPartFileName, 0, 0, 0)1 y; W- b9 q" \1 j& @$ i* f0 I
: S" z) Y9 w8 v' I# q( N! F
If (Boolstatus = False) Then swApp.DocumentVisible True, swDocPART: Exit Sub '若零件插入失败则退出
) ^& B2 C( {' I' F/ n $ U( j% ~& S0 h4 k2 c
swAssy.ShowNamedView2 "*等轴测", 7* Y9 O5 x' ?- p q) v7 I0 I
swAssy.FeatureManager.UpdateFeatureTree '更新特征树
8 h% d& j a9 j+ J) o% M, L 3 Y5 p3 g3 |5 D0 o7 C
swApp.CloseDoc sPartFileName4 s. B' D9 q$ H# e
swApp.DocumentVisible True, swDocPART7 j9 i6 q9 u: Z( a
( Z6 U8 D' R% r E6 E7 LEnd Sub( V: g* v) O; _) {" j
) T3 v- k4 a4 G1 h# q, H/ `2 f, O[ 本帖最后由 swabc 于 2009-5-26 17:24 编辑 ] |
|
