|
|
发表于 2009-7-9 18:59:56
|
显示全部楼层
来自: 中国北京
在config.pro中加入:" t) ~- i& j0 Z4 G
raster_plot_dpi 300 !设置打印分辨率; M# Z4 ?# `3 M3 V/ D2 e4 B
shaded_postscript_background no; \( F4 b: g2 k
use_software_linefonts yes !出图时使用准确线型
& B7 t4 E( V* [0 X2 }8 _; {! k& m2 O! LANDSCAPE_POSTSCRIPT_PRINT NO,打印时是否旋转90度
6 D' }6 U; m% w W) q$ C# \!pro_plot_config_dir $PRODIR/../pro_stds/plot_configs" |5 p8 A$ r ~& B- O- ~
!PLOTTER SET: To your defaut plotter2 S/ `" o& C3 p# H6 d9 X
plotter HP1055CM- H% W! f' M7 P8 I b0 m. s) g
plotter_command WINDOWS_PRINT_MANAGER
( D9 Y: N) p8 @" f& ^use_8_plotter_pens YES !设置打印机是否支持8种绘图仪笔,缺省为4种* x% }' X9 d" z$ p3 {: D! ?% D. [4 }' n
!pen1-pen8 的缺省值为 4,1,2,3,2,3,1,4;数值越大,笔宽越粗,最粗为16
0 z) u- \) a. T2 `3 J ?下面是设置系统的8种笔宽:7 O" L# Z+ K* v: N& @8 Q; J
pen1_line_weight 5
! D+ y+ E' p' o& V8 `- m; q% Fpen2_line_weight 2% ]6 E% Y4 V/ z* h8 { a, W
pen3_line_weight 24 M0 i" {% c' b
pen4_line_weight 2
# t3 h8 P$ A( }2 G" @, h0 X; open5_line_weight 2- N& h0 H0 |- W9 r4 K4 z: n
pen6_line_weight 2# f# C$ _" v! n& J2 V. a; K8 m
pen7_line_weight 2
! C. m( m: h2 T) F$ Ppen8_line_weight 2
; M$ A- G$ R# u, Y& m& Craster_plot_dpi 300
! e- i" w$ ~; e p5 \7 K' ]8 Vuse_software_linefonts yes) H/ H, s% i3 b+ A, r* ~6 z
use_8_plotter_pens YES
# [8 Z, l1 ]3 |0 ~, S! Control size of the window by either one of the following config options
1 A3 R5 y7 d4 u! {# j, Jwindows_scale 1.0- [$ h" V% _2 T
!reserved_menu_space 24 W! f& j0 V4 Y6 N8 }& E& |" v* P4 f* D
sketcher_disp_grid NO! T& P: |' D* M% s$ l; P
! Select either english or metric drawing setup files as your
& p& K; R" H8 `4 h; s' n2 Z' l4 ]. k! common default. You should refer to the "Drawing User's Guide"
# B" f" z7 g! E9 X! for a complete list of drawing setup file options.
% t3 ]$ c0 ?. Z3 K!DRAWING_SETUP_FILE D:\worker\图框proe\english.dtl
7 N6 u( F0 f" U B, x1 ~pen_table_file D:\*\**8 N" z5 x7 t$ q2 P8 E+ }
default_ang_dec_places 29 [) O3 `' e4 F5 V5 C" n1 v
create_drawing_dims_only YES
6 Q3 e: }" a# k6 A9 z. t' N1 ^highlight_new_dims YES, j2 D+ ]1 l7 w; a6 A: W
rename_drawings_with_assem YES
6 j* M8 d! u$ g. N% N* Zgtol_dim_placement UNDER_VALUE
$ @5 j* A! M: Smark_approximate_dims YES
3 _. e7 M: h& x: D- R4 Zsketcher_starts_in_2d yes
8 `' n1 i& H- C# Zplot_file_dir D:\*proe" f; P& E% K/ c
& {7 p+ M5 J4 ]
6 w ], M* s* E0 q a" e以上需要自己加入相关路径.既可(有"*"号的行); 5 f5 d7 A" A5 m! o) S8 N
除了"pen1_line_weight "是实体线外,其余线宽3 d2 ^7 ]9 x6 O w5 I+ ^! E
同样自行设置.其中数值根据使用情况修改.以上1 i5 ]1 S0 j2 |7 ~2 F/ y& f2 j7 c' M
连同说明一起放在config.pro中- S+ M$ L' e# [
# [* z" k" p3 ~0 I# L- d$ d[ 本帖最后由 hhq426 于 2009-7-9 19:06 编辑 ] |
|