|
|
楼主 |
发表于 2011-7-28 05:20:31
|
显示全部楼层
来自： 加拿大
. @/ O+ \ `0 F* G& h& I4 \
& U n0 X& ?0 C! ?4 Q: f. F9 q" @, h0 e
全世界都知道，但说说方法吧 - @9 C( X6 Y( {1 \& t. h' A# R# ?
- I3 [8 o9 g) x( t; m, y- x我现在用工单的方法输出， 但这方法读不出没有用到程序上的刀夹。
4 D. m4 ^) D' S8 e1 e8 O. b! X% Q @
0 y) T+ p: R# F ^令一方法是读进刀具数据库再输出， 但效率不好。5 c( V! E1 I" f. @5 v3 o* B$ l
# w6 z0 R( |) x1 {* a1 gype,Name,Number,Diameter,Length,Tip Radius,Chamfer Angle,Chamfer Length,X Offset,Y Offset
7 `* s/ D x/ A/ ?, V: z) J4 o; T) {
Ball,1,0,10.0,50.0,0.0,0.0,0.0,0.0,0.05 d4 A* o- G4 B4 X7 l# `: U
Holder********************************************
+ g3 n3 S7 K9 o6 c I0.000000000000000 0.000000000000000 0.000000000000000
2 r4 D, v& K8 L/ \! v12.800000000000001 0.000000000000000 0.000000000000000) L, F' H! G9 h, [
16.070000000000000 0.000000000000000 17.050000000000001
" i$ i8 |2 y; J16.070000000000000 0.000000000000000 41.500000000000000
0 _) V: ?& K5 E9 I9 I2 O25.170000000000002 0.000000000000000 46.7300000000000045 [8 i* C6 k+ [0 X. m$ Z
25.170000000000002 0.000000000000000 60.860000000000007* W [8 X, p% }+ H! Q. e
31.350000000000001 0.000000000000000 60.860000000000007
) O7 D5 F( R8 S( a+ S9 x31.350000000000001 0.000000000000000 86.830000000000013
' i8 M- X3 n5 \2 L# x2 Q( Y9 O3 P
" v5 X. a* v# Q2 L9 R* }4 Z( DBall,2,0,10.888,54.44,0.0,0.0,0.0,0.0,0.0/ M; W3 A' z& H) V
Shank--------------------------------------------
9 U$ a: _$ E- e# {) m4 j0.000000000000000 0.000000000000000 0.000000000000000
5 w+ K* _ z7 N( `5 ?0.000000000000000 0.000000000000000 54.4399999999999987 u4 J( ?% f7 U) `5 @% s
8.166000000000000 0.000000000000000 54.439999999999998
3 x; T0 Q0 B/ V, f$ B$ S8.166000000000000 0.000000000000000 108.880000000000000
; R' u" ?6 v, ?6 h6 _0 c; D1 K: b! m" z& M! R
Ball,2_1,0,10.888,54.44,0.0,0.0,0.0,0.0,0.0
4 i: U; z u# X- `6 r0 fShank-------------------------------------------- n8 c# {3 K2 ?
0.000000000000000 0.000000000000000 0.000000000000000( \0 ^2 I( p" f1 {" G
0.000000000000000 0.000000000000000 54.439999999999998- m, C9 P' m$ h, ]1 a
8.166000000000000 0.000000000000000 54.439999999999998; y0 F) O5 ], Q# W1 K* [! W
8.166000000000000 0.000000000000000 108.880000000000000$ W! w9 r& E# s% F7 P) x
( S5 K! ]4 _* d$ STap,3,0,10.888,54.44,0.0,0.0,0.0,0.0,0.07 N! \+ b2 r: K7 y! L4 g
Shank-------------------------------------------- n% p7 T" u+ I6 z
16.332 16.332 54.44 0 |
|
发表于 2011-7-19 21:46:53
