|
|
发表于 2014-8-19 14:03:52
|
显示全部楼层
来自： 中国辽宁沈阳
Sub main()
2 @) I! P; I0 v0 s* U5 m$ dSet swApp = Application.SldWorks
, I7 E/ Z+ P6 e" g2 I* \Set DrawingDoc = swApp.ActiveDoc4 O% q3 ~3 m x% W5 L
If DrawingDoc.GetType <> 3 Then Exit Sub
9 n; e" r, k, A* |6 j SSet SelMgr = DrawingDoc.SelectionManager8 S, }' M6 a4 n/ ^4 n
If SelMgr.GetSelectedObjectType2(1) <> 12 Then Exit Sub1 A+ H$ K" h2 Y, ?
Set swview = SelMgr.GetSelectedObjectsDrawingView(1)
" d2 G% X( s5 P6 q; LSet swDrawComp = swview.RootDrawingComponen
/ N5 S4 K0 e* d v1 rDrawingDoc.ActivateView swDrawComp.View.GetName2) ?5 n2 m* D( v3 w* C* ~
Set Part = swview.ReferencedDocument3 K' W# V! t0 k W2 x
Set FeatObj = Part.FirstFeature
: S4 E. ?+ [6 ?$ @/ x/ j5 \FeatObjname = FeatObj.GetTypeName
4 s! [/ [6 |; }& G5 W+ Q" f e* xWhile FeatObjname <> "OriginProfileFeature"
" M9 d5 t# U( A1 C/ r) s! ` Set FeatObj = FeatObj.GetNextFeature
# w0 V( E3 m) a4 X6 d) O FeatObjname = FeatObj.GetTypeName
1 D$ ^2 A; M& F2 P# s% V& QWend
0 w( q( j5 v# D3 NFeatname = FeatObj.Name, @% z( F9 p# y- u& k
ViewOutlines = swview.GetOutline
: x" M+ l* t0 {! g/ I% ZViewCXform = swview.GetXform: L" B K" o' v& o( [6 z9 K
ViewXform = swview.GetViewXform. M( }* a; B3 z$ a% R- ~* A1 l
Hp1x = (ViewOutlines(0) - ViewCXform(0)) / ViewXform(12)
/ t. b6 O! e" o5 @4 C- dHp1y = ((ViewOutlines(1) + ViewOutlines(3)) / 2 - ViewCXform(1)) / ViewXform(12)
% z5 s% F& m1 B- _Hp2x = (ViewOutlines(2) - ViewCXform(0)) / ViewXform(12)+ z) W4 \& W; Q' }5 ^! P2 b
Hp2y = Hp1y
3 s( a, Z0 P- rVp1x = ((ViewOutlines(0) + ViewOutlines(2)) / 2 - ViewCXform(0)) / ViewXform(12)5 [$ ?& p+ P3 ?: V6 Z
Vp1y = (ViewOutlines(3) - ViewCXform(1)) / ViewXform(12)
3 o( z( c% ? G7 L+ M2 _2 eVp2x = Vp1x
% g) Y# `5 ?) bVp2y = (ViewOutlines(1) - ViewCXform(1)) / ViewXform(12)
! P4 ?5 o' y' qDrawingDoc.SetAddToDB (True)
A) K( w# M U( u* \7 [( \9 gSet SkLineH = DrawingDoc.SketchManager.CreateCenterLine(Hp1x, Hp1y, 0, Hp2x, Hp2y, 0): K( l+ V( T+ u2 n3 E
DrawingDoc.SketchAddConstraints "sgHORIZONTAL2D" v6 k1 S7 u' ]& U- ~" j
boolstatus = DrawingDoc.Extension.SelectByID2("Point1@" & Featname & "@" & swDrawComp.Name & "@" & swDrawComp.View.GetName2, "EXTSKETCHPOINT", 0, 0, 0, True, 0, Nothing, 0)
( Z4 S+ x* }: S" ?- O, V8 a( J& ADrawingDoc.SketchAddConstraints "sgCOINCIDENT"( T5 f) z6 Z) n2 d
Set SkLineV = DrawingDoc.SketchManager.CreateCenterLine(Vp1x, Vp1y, 0, Vp2x, Vp2y, 0)5 v; n$ g/ K! y- C- _6 k" D
DrawingDoc.SketchAddConstraints "sgVERTICAL2D"
i# ?. E1 z, K8 l2 }3 _boolstatus = DrawingDoc.Extension.SelectByID2("Point1@" & Featname & "@" & swDrawComp.Name & "@" & swDrawComp.View.GetName2, "EXTSKETCHPOINT", 0, 0, 0, True, 0, Nothing, 0)7 J, X- j( ~! i2 d _9 l0 P) N" C5 Z
DrawingDoc.SketchAddConstraints "sgCOINCIDENT"
1 r+ i, S7 |* GDrawingDoc.ClearSelection2 True
, G! ~$ ?3 o ^% u& m. b$ ?End Sub |
|
![002902l7x7ddilsxd8losd[1].gif](data/attachment/forum/201408/19/123120fqaceahtic2oawdc.gif "002902l7x7ddilsxd8losd[1].gif")
楼主
$ b/ D! T1 A/ S& Q4 Q