|
|
楼主 |
发表于 2014-12-29 20:07:39
|
显示全部楼层
来自： 中国河南洛阳
* _! t! J u# M
一直用的是“控制器”，这次试了下“磨损”确实理想了: K1 s2 r I" N
“控制器”( k* G% X- z( s$ b2 L9 v
N106 G0 G90 G54 X-10. Y-30. S1000 M3% o! n+ U9 b9 c) V+ I6 i6 b
N108 G43 H1 Z25." d& E& F( h, d/ F( U4 R0 |5 ^
N110 Z2.
( w9 `8 D$ `& |. qN112 G1 Z-1. F1000.# }, \- R' |( {) J9 Z1 w
N114 G42 D1 Y-20. F200.! ~4 O. l. _! W; f4 }( A0 q' \3 e" n
N116 G2 X0. Y-10. I10. J0.
/ ~* ~/ p1 ^1 @/ M5 [6 |N118 G1 X10.
1 B3 z7 }7 e/ TN120 G3 X20. Y0. I0. J10.) \) m( P# g" v( h
N122 X10. Y10. I-10. J0.; `/ _) d N5 q3 C$ O. {
N124 G1 X-10.& v. o# X, }4 c
N126 G3 X-20. Y0. I0. J-10.' C: [5 Z, |: |
N128 X-10. Y-10. I10. J0.
1 l1 G0 Z( k" J t, _$ fN130 G1 X0.% x9 q. u! m% r# ?8 U* M8 h! [
N132 G2 X10. Y-20. I0. J-10.
4 S* k3 T& Y. H% ?% r) O4 YN134 G1 G40 Y-30.) i( H2 V0 f( @ c$ w
N136 G0 Z25.
; B8 h/ W( x* m N“磨损”
* e Q+ Z5 ]$ o- k5 dN106 G0 G90 G54 X-10. Y-35. S1000 M3
0 a* ?* g) I4 u1 {N108 G43 H1 Z25.
" d$ Y3 i, W( F4 s$ XN110 Z2., s3 ?# P% w6 p( v- _
N112 G1 Z-1. F1000.
3 U8 v* {& f, }( m" l. `( w& M: l8 KN114 G42 D1 Y-25. F200.
m( |% M. a W# i6 RN116 G2 X0. Y-15. I10. J0.5 H* \9 }" @# W* A6 K" @
N118 G1 X10.
+ H9 C- o2 \/ C! h' q; ]; gN120 G3 X25. Y0. I0. J15.
( y6 t% I8 k+ f) z) A9 R* nN122 X10. Y15. I-15. J0.! n8 }" R5 w( k; o3 m D; G
N124 G1 X-10.
0 d2 N* D' l; X1 z( ^# x! O; c" dN126 G3 X-25. Y0. I0. J-15.
& s9 |1 z3 P( y# w% VN128 X-10. Y-15. I15. J0.3 k2 L+ p4 d7 [) _
N130 G1 X0.+ g9 v+ l B- m- K
N132 G2 X10. Y-25. I0. J-10.
8 p% s5 _* ^/ e5 P9 E- ?# e' gN134 G1 G40 Y-35.6 c0 Z H! M s3 m7 e+ c& Y2 P- q
N136 G0 Z25.
+ b- |9 s7 \1 n7 J( j6 r谢谢指点 |
|
发表于 2014-12-28 20:40:04
