|
|
马上注册，结识高手，享用更多资源，轻松玩转三维网社区。
您需要 登录 才可以下载或查看，没有帐号？注册
x
本帖最后由 lyd_2005 于 2015-10-23 13:54 编辑
4 o. Q. ?; w5 ?8 r- ^3 k) q: f" l) V8 v
, a% c" [& h# n* r5 G: S/ }
( C, z5 H5 `2 b& d
5 Z" ?8 \7 ]: k* `
1.查找 ptap$ #Canned Tap Cycle
+ K- C$ b8 w* ^& v/ [ H
+ j F# F6 N; O8 W7 P. `6 q8 e( Q
1 \7 R% h8 G4 e* W: y 到 pcom_movea 中间部分修改为$ D, A/ u# i* L0 M R" D
ptap$ #Canned Tap Cycle; h, c5 E5 K# T9 x) }5 r8 I2 C
pdrlcommonb
4 ?9 {: N, J. k; v if peck2$ = 0,( D9 J; o' J5 i; U. _. Q
[* S; B+ j A S' ~0 `' [! m
#RH/LH based on spindle direction" a6 P! x# O* p
if rigid_tap, pbld, *sm29, *speed, e$ #Rigid Tapping7 [ K' E: U; K: R
pcan1, pbld, *sgdrlref, *sgdrill, pdrlxy, pfzout, pcout, pindexdrl,- I: o. ]* {; |
prdrlout, [if peck1$, *peck1$], *feed, strcantext, e$0 C! c- w' z) F/ Q! ?
]
# @& _: j- s: l+ j. U& E- t& q else,; n# f% R" @% z
[/ `# q% C# v' F# w7 {* U* F
"M03",*speed, e$1 X) Z0 G* d4 h2 O) N
"G94", e$$ w1 p* k7 q! u- C# {
if metvals, pitch = n_tap_thds$ # Tap pitch (mm per thread)
$ k( [* L; t; b; \4 W else, pitch = 1/n_tap_thds$ # Tap pitch (inches per thread)
9 {3 _7 z3 {' ?( J1 X; C0 w) q pcan1, pbld, *sgdrlref, *sgdrill, pdrlxy, pfzout, pcout, pindexdrl,* o0 @" V" H& O6 o
prdrlout, [if peck1$, *peck1$], *pitch, !feed, strcantext, e$/ L, m- h- ~3 d+ a
]3 M8 O& D6 \5 o( S$ V6 B8 p( Z+ i
pcom_movea' R. n* p$ H- M) j5 c
2. [tap]* g s) G' @: Z6 {
1. "G84/G74 - Tap"$ M5 d$ ]( P7 c5 Z. d
3. ""0 v& W& l6 l0 w+ f9 O
7. "Peck"- |4 A6 W9 Z0 b. s/ U) J/ w
8. 将 "" 修改为 "0为G95方式，1为G94" 要冒号（有两处）0 ^2 [* O6 i9 }! G0 z) |
9. ""
/ ^" Y8 a' n$ o9 Y! d1 W5 n 10. "": f- v- k( m6 G" z4 R% s: N: h
11. ""; n+ I; J8 _# t; a( `7 S/ _
3. pcanceldc$ #Cancel canned drill cycle
2 K: j. p3 B: x) l/ t0 T result = newfs (three, zinc)
: M9 j8 f' ?1 O if drillref = 0, zabs = initht_a #Make the initht the modal Z value# z" U }& K! ?
else, zabs = refht_a
8 o. X: x. f3 n9 k# d" R prv_zia = zabs) i, C6 P( I1 T2 q/ G F6 p5 a
!zabs
: b( |3 ~) O& w0 F( F: [# A, d ps_inc_calc3 P4 ?; m; O' D+ R: n' g
prv_gcode$ = zero3 M! \& g. j, _) O* T: |4 s. o
if cool_zmove = yes$ & (nextop$=1003 | (nextop$=1011 & t$<>abs(nexttool))), coolant$ = zero& o2 Q. B8 V, }
pcan0 d5 {( }& S7 N4 d! s* B% o k1 |
if drillcyc$ <> 8, pcan1, pbld, "G80", scoolant, strcantext, e$' K8 d7 [2 }, p: ~, B
if peck2$ = 1,"G95", e$ 增加此行
/ l1 n4 W- O! `5 E, d. Z1 v #pbld, sgfeed, e$3 r: n. C( k( x- |3 v/ c
pcan2; y+ z7 Z1 [2 P! y5 S
因本人不使用此功能，只是一个思路，以上G94，G95,自行调整。
0 H' ^! }$ @& P- {) n1 u) Q
, w- I1 B2 o6 K8 `8 \7 b" q/ S8 i1 y! S9 M) G9 Q
) ?+ a2 Y8 O# s; Z8 R
|
|
发表于 2015-10-23 12:14:04
楼主
