|
|
发表于 2019-12-8 22:50:36
|
显示全部楼层
来自： 中国吉林
以默认MPLFAN为例,搜索 , C; B P! {- c' P) Y) @: S
psgcode #Output the Gcode based on the current plane
w2 s+ R% m% V5 K1 V4 U; I/ V找到代码1 O8 M/ ?9 H P9 ~ ~
psgcode #Output the Gcode based on the current plane# l" E) I: I0 w8 ?, h
if c_ax_flp,( w) Z5 }6 k2 ` C# T3 V
[ p3 t$ @* o+ h" n, S
#Reverse arc direction for c_axis flip
" C' U7 H j9 ~7 l# C; m+ t3 R if gcode$ = two | gcode$ = three,
4 L4 r: ]4 x/ z1 {9 j' b$ Q# q [4 g* _5 C. {' M4 c' r
sav_gcode = gcode$
8 Q X' P9 q+ ~6 P* o gcode$ = (5 - gcode$) #G02->G03 or G03->G029 O5 d2 p, _+ h- Z1 B; Q( ^# c3 i
]
6 F6 t" q( z( X- V ]
0 W h+ y9 s( ~. f if plane$ = zero, `sgcode6 O) l" ]% |7 [3 f% v
if plane$ = one, `sgcode1
8 l* s G" B/ a# G6 f6 l if plane$ = two, `sgcode2
& }5 _5 Z* r/ H" f1 F if c_ax_flp, gcode$ = sav_gcode& W8 y, G4 d/ f5 ?9 o2 p# T
* A/ o5 Y# j% L' F1 s, ~5 G, q
加点作料改为
+ l0 }7 u! u0 J' l, l/ {5 zpsgcode #Output the Gcode based on the current plane
5 G p# `- _3 O if c_ax_flp,
$ U5 D$ x! ?/ _5 v) r+ D [* }" `1 i6 I q2 i% Q! a
#Reverse arc direction for c_axis flip
3 G0 y" P% ^7 q! F3 n. b: q if gcode$ = two | gcode$ = three,5 d: K$ @" G3 \! K' m- N
[% p9 A1 I3 N, m9 P6 N
sav_gcode = gcode$
( Z% E/ j4 }; A+ }7 J3 [ gcode$ = (5 - gcode$) #G02->G03 or G03->G02. }% P( \; g7 ]% w% N% z2 d4 [
]# O3 X. \% A% R5 Q; n- M4 ^" x
]
0 t& I* K/ w7 \% u0 u1 { if gcode$ = 2 | gcode$ = 3, result = force(gcode$)4 t* h m( L. y6 S# }
if plane$ = zero, `sgcode F& D0 U& G- B, E. J
if plane$ = one, `sgcode1
, X& Y1 q3 S/ d4 A$ h- v& X if plane$ = two, `sgcode2
6 ~/ n: |% O0 q8 I2 Q- ` if c_ax_flp, gcode$ = sav_gcode3 j; d9 ?4 W. K; w
保存 完事 |
|
发表于 2019-12-8 13:42:50