|
|
楼主 |
发表于 2007-2-10 23:56:58
|
显示全部楼层
来自： 中国江苏南通
我是这样做的，可不行．" X% K# @6 z' Y7 E1 P Y' V9 l
运行后生成的几个视图不一样大，（虽然比例已设为一样），每个视图中显示不全整个零件，虽然加ＡＵＴＯ能显示出整个零件，可各个视图里的零件不一样大（长宽没有投影关系），, Z8 w" ~, z- d) S: u# u
而且运行好ＧＲＩＰ后只要手动一移运视图，就又变成都了没有auto前的样子．
! H) M' ~1 _" Udrawc/'ele',mmeter,210,297,iferr,mess:
$ G; {+ f/ ~1 T7 `drawe/add,'top',40,200,iferr,term:5 V3 V. Z0 j: [+ l
drawe/add,'front',40,50,iferr,term:
& y/ D/ T* ?9 Udrawe/add,'right',150,200,iferr,term:% N# N: r, p+ H
drawv/'ele',na
+ c5 `2 x* Q( U3 L3 f" Y: ?drawe/'ele',dvstat,na(1),active
- z% k" c: x hviewe/na(1),center,70,150,save9 T2 o- [& M5 P- r9 L$ Z
viewe/na(1),auto,save
" ^) s" |& L$ j7 `( |viewe/na(1),scale,0.2,dscale,0.3,save& f7 [: l% b6 k8 N/ Q9 ~. A1 l
viewe/na(1),auto,save
) B4 `2 x! i+ k i* p3 i3 Zdrawe/'ele',dvstat,na(2),active! j% @# q: h' E- k- I
viewe/na(2),center,70,50,save
9 F7 l5 t: O* Z7 C5 a( v0 n7 D# Lviewe/na(2),auto,save; ~/ |# i9 q! \ J0 p: U; A' q0 [! J- u
viewe/na(2),scale,0.2,dscale,0.3,save& M" _! W2 X. D( z1 q
viewe/na(2),auto,save
; L0 U7 o, k$ r4 ]# c, c7 n/ tdrawe/'ele',dvstat,na(3),active1 z' I3 k; K4 I3 X! v" @7 l2 L6 g
viewe/na(3),center,210,50,save
9 t. H! ^2 h, P h9 yviewe/na(3),auto,save- D9 a2 M+ r. C! J$ p8 ]
viewe/na(3),scale,0.2,dscale,0.3,save% I8 }, {- U+ e
viewe/na(3),auto,save
2 R+ a2 D' M0 H+ I9 w7 c0 y* M' Y9 r- U- O0 B. _2 Y }) v6 G
出个图都这么难搞定．不知大哥你的程序也是这样一个加图纸，加视图，改视图的过程？不太明白你上面这一贴的意思．/ g3 R9 ]+ u& j, |0 N
4 i" t X. |+ x- K
[ 本帖最后由 zgjshahxm 于 2007-2-11 00:16 编辑 ] |
|
发表于 2007-2-8 23:08:45
