为什么整圆工件而程序却是很多小段?

linxiao3dportal

% Y& y+ ~8 e$ z
为什么整圆工件而程序却是很多小段?甚至有的被处里成直线,这样的程跑起来很慢,而且也漂亮!
N0030 G00 G90 X19.126 Y-28.431 S2000 M03  M08
9 C$ k, i  r' {: F! xN0040 G00 Z33.
N0050 G00 Z27.
N0060 G01 X19.126 Y-28.431 Z24. F800.
  r2 q' @! `! T5 R! WN0070 G03 X13.129 Y-28.375 I-3.057 J-6.297
& b2 ~, q. c5 ^6 Z! gN0080 G02 X10.821 Y-29.333 I-13.127 J28.368
$ y6 s; c' I& Z$ s: C; s5 GN0090 G02 X-8.776 Y-30.008 I-10.819 J29.326
( a' h! g/ i9 h8 R9 @. |N0100 G02 X-21.544 Y-22.655 I8.684 J29.842
: M' @! w, }& c4 u$ vN0110 G02 X-22.655 Y-21.544 I20.752 J21.863
N0120 G02 X-30.797 Y-5.386 I22.515 J21.476
N0130 G02 X-26.285 Y16.927 I30.787 J5.388
N0140 G02 X-8.776 Y30.008 I26.282 J-16.922
  e3 q/ G3 s& m* j& e0 c# ^N0150 G02 X16.927 Y26.285 I8.776 J-30.003
! c1 Y# ^# o, AN0160 G02 X25.227 Y18.466 I-16.827 J-26.177
N0170 G02 X26.16 Y-17.119 I-25.213 J-18.466
1 K. o. A  L+ ^' q' L" zN0180 G02 X10.821 Y-29.333 I-26.158 J17.112
- G- U- B+ U4 m% V9 o  ]& w4 Y- x& R0 uN0190 G01 X10.47 Y-29.499 Z23.897
N0200 G01 X10.117 Y-29.662 Z23.793
* i8 `7 G" L  G0 l# q/ cN0210 G01 X9.761 Y-29.82 Z23.69
N0220 G01 X9.404 Y-29.974 Z23.586
  l2 H; O" z0 k3 e# D, CN0230 G01 X9.044 Y-30.125 Z23.483
7 O$ Z$ P$ O1 I- \N0240 G01 X8.682 Y-30.27 Z23.379
' s- T: e+ B! t" c8 {/ g7 f3 BN0250 G01 X8.317 Y-30.411 Z23.276
N0260 G01 X7.951 Y-30.548 Z23.172
. I% Y; `* N* r, Z4 C! b( EN0270 G01 X7.582 Y-30.681 Z23.069
2 x7 O! i& j. k  E. `N0280 G01 X7.211 Y-30.808 Z22.966
N0290 G01 X6.838 Y-30.932 Z22.862
3 \6 a' A6 S* h# X% r$ Z0 {N0300 G01 X6.463 Y-31.05 Z22.759
( d! @$ X+ i0 DN0310 G01 X6.086 Y-31.165 Z22.655
N0320 G01 X5.708 Y-31.275 Z22.552
) H& ?- E# L3 T, O# D: J7 sN0330 G01 X5.328 Y-31.38 Z22.448
N0340 G01 X4.946 Y-31.48 Z22.345
N0350 G01 X4.562 Y-31.577 Z22.241
, j3 V2 Q7 K- Y# a8 L% {" pN0360 G01 X4.177 Y-31.668 Z22.138
' V& w5 ]  M" c" pN0370 G01 X3.79 Y-31.755 Z22.034...............................................(这么简单的刀路就有300多段程序?)

zp840621

呵呵 长见识了                    楼主高手啊

linxiao3dportal

请高手多多指点

jianyu13

在机床输出的时候给个参数了，然后看看后处理有没有问题了。