2004一般会在编辑过工具栏后自动保存一次acad.mnr文件，下次启动时就会显示编辑后的工具栏；
2 ] g2 X3 t8 n+ M按下面打开菜单文件，保存一下；9 t* C( p: i ?9 G" N' g
或者找到里面的对应工具栏项直接修改，再保存；
( ^- v% u/ E4 E! m: u: k5 w! L找到下面的代码段：
/ ?* N: ]3 o% p# T; L**TB_MODIFY0 _4 ?& L4 u/ c- `8 \( \
**修改
2 v& l! b9 A; N$ O( z7 k; NID_TbModify [_Toolbar("修改", _Left, _Show, 1, 0, 1)]4 Y& u7 C- i( I# J) L4 e& x9 y
ID_Erase [_Button("删除", "RCDATA_16_ERASE", "RCDATA_16_ERASE")]^C^C_erase / u1 l# r9 R+ Y9 e, L
ID_Copy [_Button("复制对象", "RCDATA_16_COPYOB", "RCDATA_16_COPYOB")]$M=$(if,$(eq,$(substr,$(getvar,cmdnames),1,4),grip),_copy,^C^C_copy)
. n" y" e+ T: p( s iID_Mirror [_Button("镜像", "RCDATA_16_MIRROR", "RCDATA_16_MIRROR")]$M=$(if,$(eq,$(substr,$(getvar,cmdnames),1,4),grip),_mirror,^C^C_mirror)
/ X0 o: x! f6 @$ Q gID_Offset [_Button("偏移", "RCDATA_16_OFFSET", "RCDATA_16_OFFSET")]^C^C_offset
4 }9 M1 }5 h M+ e2 f0 c& f/ iID_Array [_Button("阵列", "RCDATA_16_ARRREC", "RCDATA_16_ARRREC")]^C^C_array
9 i' d1 {( W, y+ y6 xID_Move [_Button("移动", "RCDATA_16_MOVE", "RCDATA_16_MOVE")]$M=$(if,$(eq,$(substr,$(getvar,cmdnames),1,4),grip),_move,^C^C_move) % `( c5 e4 D7 Q) x( f
ID_Rotate [_Button("旋转", "RCDATA_16_ROTATE", "RCDATA_16_ROTATE")]$M=$(if,$(eq,$(substr,$(getvar,cmdnames),1,4),grip),_rotate,^C^C_rotate)
$ d1 l7 A, U' ]! w0 ZID_Scale [_Button("缩放", "RCDATA_16_SCALE", "RCDATA_16_SCALE")]$M=$(if,$(eq,$(substr,$(getvar,cmdnames),1,4),grip),_scale,^C^C_scale)
4 o+ {7 \: F& a U: xID_Stretch [_Button("拉伸", "RCDATA_16_STRETC", "RCDATA_16_STRETC")]$M=$(if,$(eq,$(substr,$(getvar,cmdnames),1,4),GRIP),_stretch,^C^C_stretch) $ @2 p; @$ ?+ h! p
ID_Trim [_Button("修剪", "RCDATA_16_TRIM", "RCDATA_16_TRIM")]^C^C_trim 5 D9 r$ O& P; K6 ^7 U% o% x
ID_Extend [_Button("延伸", "RCDATA_16_EXTEND", "RCDATA_16_EXTEND")]^C^C_extend
: |. q- r3 t4 c3 m' yID_BreakSele [_Button("打断于点", "RCDATA_16_BREAKATPT", "RCDATA_16_BREAKATPT")]^C^C_break \_f \@ 1 q1 x, e% H+ h
ID_Break [_Button("打断", "RCDATA_16_BRE2PT", "RCDATA_16_BRE2PT")]^C^C_break
+ D% n3 v- m2 Y1 M1 YID_Chamfer [_Button("倒角", "RCDATA_16_CHAMFE", "RCDATA_16_CHAMFE")]^C^C_chamfer
: l" V6 A! p" m0 l/ |' kID_Fillet [_Button("圆角", "RCDATA_16_FILLET", "RCDATA_16_FILLET")]^C^C_fillet ' s* {7 f% R1 S3 u- b9 C; }
ID_Explode [_Button("分解", "RCDATA_16_EXPLOD", "RCDATA_16_EXPLOD")]^C^C_explode ( b: G6 C* w+ K+ f0 ], |9 c u
ID_Hatchedit_0 [_Button("编辑图案填充", "RCDATA_16_HATEDI", "RCDATA_16_HATEDI")]^C^C_hatchedit （要增加的代码）
- r& Y5 _2 C* E$ g" ~- k% F0 B8 H: b/ [, }7 F* A/ F9 S4 c2 |
然后卸载ACAD菜单文件，再加载ACAD.MNS菜单文件即可；( K K, o; ~9 T" e3 R6 y$ R
# y. ]) M! O# M( g
" h3 ~% m+ C' z4 s$ z4 J% h[ 本帖最后由 sealive_leafage 于 2008-6-4 15:56 编辑 ] |
发表于 2008-6-4 14:36:27
发表于 2008-6-4 15:38:44
发表于 2008-6-4 15:50:59
楼主