|
|
马上注册，结识高手，享用更多资源，轻松玩转三维网社区。
您需要 登录 才可以下载或查看，没有帐号？注册
x
Composite Materials： Design and Applications (CRC 2003)( a# f- d- M3 V2 p$ e
page：523
$ t$ |- S8 T/ G8 X" A" I1 P0 f$ N1 E! o4 V) h- W6 \
French editions published by Editions HermEs, Paris, 19973 z) Y& I: W* A8 K) m+ C# B
No claim to original U.S. Government works% b* E9 g/ f J5 d
International Standard Book Number 1-58716-084-61 q9 K3 h: _( e4 M# u9 y# D; {
Library of Congress Card Number 2002073794
, Y8 @& g3 I. f2 r; Z5 Z% g l简介
1 H" q0 |, W2 u/ ?7 x6 I" _This book contains information obtained from authentic and highly regarded sources. Reprinted material is quoted with/ k+ B! e5 O1 `
permission, and sources are indicated. A wide variety of references are listed. Reasonable efforts have been made to publish
C0 |8 Y8 C! n+ X# y. areliable data and information, but the author and the publisher cannot assume responsibility for the validity of all materials2 i- ~7 G' W6 T) u
or for the consequences of their use.
, s2 \* |& H9 L8 r e1 Composite Materials, Interest, and Properties: ]* \- u4 D0 p% N
1.1 What Is Composite Material?
7 n: r* b' m( `" S1.2 Fibers and Matrix
; w; d( p) s* V1 C) U& ?1.2.1 Fibers
$ V* K4 _! c5 N# Z1.2.2 Matrix Materials
; k" G6 z5 z; d8 c1.3 What Can Be Made Using Composite Materials?
: h6 W' o* \" s0 N: n1.4 Typical Examples of Interest on the Use of Composite Materials
2 A1 Y. n1 l3 W# P/ _1.5 Examples on Replacing Conventional Solutions with Composites 2 k+ F* ^) L+ z }! F M
1.6 Principal Physical Properties 8 T3 F7 _7 X' j% s u, ?* w
2 Fabrication Processes8 t% Q; P8 e6 y, C
2.1 Molding Processes 3 }- R) x$ v, R2 q" p
2.1.1 Contact Molding
! p r$ c/ I3 l2.1.2 Compression Molding % Q3 J4 u. ^1 I- d4 u7 A
2.1.3 Molding with Vacuum
$ v' }% J, Y! d1 |( p2.1.4 Resin Injection Molding 1 C, ~- u) t# [
2.1.5 Molding by Injection of Premixed 7 {/ B! H- M f4 P
2.1.6 Molding by Foam Injection $ K# _* F+ ?6 O1 H% I
2.1.7 Molding of Components of Revolution
! e0 ]0 g0 D0 J$ D2.2 Other Forming Processes 0 h! M. y+ p# u$ d
2.2.1 Sheet Forming
0 v+ z0 O% Y3 t+ W9 H8 m2.2.2 Profile Forming [( n; G4 Q" Z x$ D
2.2.3 Stamp Forming
. c: t% Q, _5 h7 M$ |3 }1 z2.2.4 Preforming by Three-Dimensional Assembly 6 Z- f F- l7 _& E
2.2.5 Cutting of Fabric and Trimming of Laminates " w% y( N* S7 N4 H$ t
2.3 Practical Hints on Manufacturing Processes , L- D l3 s: U
2.3.1 Acronyms
; g1 f6 F# W$ S, |0 b2.3.2 Cost Comparison
7 B# X K# x4 l; ]5 T3 Ply Properties3 I: _' S" t: m. U
3.1 Isotropy and Anisotropy
$ H' C' S4 P% k$ i" a3.1.1 Isotropic Materials
$ V7 F1 N' ]. H" v+ \3.1.2 Anisotropic Material 2 H; z% g/ f5 [0 U0 D( q
3.2 Characteristics of the Reinforcement–Matrix Mixture
D& J v4 W5 F' z* p: f: D3.2.1 Fiber Mass Fraction
$ D$ ?0 b8 X. W; v3.2.2 Fiber Volume Fraction ; }/ `! m" i2 c3 K# {9 `- y$ b
3.2.3 Mass Density of a Ply $ W& V% `3 a5 X2 s. E* @% h
3.2.4 Ply Thickness
! k' q0 I: B& L) B...............
$ _ t$ N3 u3 k, b8 ^共9个压缩卷，解压后18.3M
4 n' x5 o$ b. ]' l7 o/ c* K# t7 b/ m
1 e1 k! L3 t2 u[ 本帖最后由 fenglianxiang 于 2008-8-5 16:43 编辑 ] |
评分
-
查看全部评分
|
[复制链接]
发表于 2008-8-5 16:37:59
