|
|
楼主 |
发表于 2012-4-10 20:20:54
|
显示全部楼层
来自： 中国天津
本帖最后由 86843173 于 2012-4-10 20:24 编辑 ( ?! y9 c B4 V5 `- f
! z+ G( f1 {7 a7 K
我说的是车床. e: [+ x, h% _. D2 ]& B
# Format statements - n=nonmodal, l=leading, t=trailing, i=inc, d=delta
/ H7 P( c' W+ b8 D5 x" L, p* A# --------------------------------------------------------------------------
; w$ O$ J) @6 t1 Z3 C1 E: n#Default english/metric position format statements& A q* |% Y, X3 P# x# G
fs2 1 0.7 0.6 #Decimal, absolute, 7 place, default for initialize ( : |7 a& t8 h) K9 q
fs2 2 0.4 1.3l #Decimal, absolute, 4/3 place" T) A* U. q1 a- `7 h, Y% ^, d
fs2 3 0.4 1.3ld #Decimal, delta, 4/3 place. e( O; e( b; ^3 f
#Common format statements
) l. C7 r1 N2 Qfs2 4 1 0 1 0 #Integer, not leading. m' U' G/ ]3 f3 x3 }7 R- d& W u
fs2 5 2 0 2 0l #Integer, force two leading9 s$ I1 f8 ~) ]) v6 ^- {; w6 q
fs2 6 3 0 3 0l #Integer, force three leading
. @3 D/ e8 k# p& V- {fs2 7 4 0 4 0l #Integer, force four leading# C# y5 m% g$ F5 K
fs2 9 0.1 0.1 #Decimal, absolute, 1 place/ m' i b" I. `4 y
fs2 10 0.2 0.2 #Decimal, absolute, 2 place
" d+ `$ {: N, q& G! |fs2 11 0.3 0.3 #Decimal, absolute, 3 place3 u. t/ G) y3 b5 g8 \
fs2 12 0.4 0.4 #Decimal, absolute, 4 place
% F) y2 k1 C- L9 D" Ofs2 13 0.5 0.5 #Decimal, absolute, 5 place
! F2 W" v! n* Y+ ]0 ufs2 14 0.3 0.3d #Decimal, delta, 3 place
& Z/ @7 ^6 H, }7 l+ Y/ @, wfs2 15 0.2 1.1l #Decimal, absolute, 2/1 place (feedrate) 就是这里
0 J/ \$ V6 V6 [. B8 C$ Qfs2 16 0 4 0 4t #No decimal, absolute, 4 trailing& j( j8 [3 l+ d- s: v
#Default english/metric feed format statements
5 h, }; Z% r& ]0 i6 ofs2 17 0.2 0.1 #Decimal, absolute, 2/1 place2 n1 e9 ]7 U9 c; i( D* p" m0 \
fs2 18 0.4 0.3 #Decimal, absolute, 4/3 place
: R" a/ p. _. n. A dfs2 19 0.5 0.4 #Decimal, absolute, 5/4 place; E2 D4 U! H& D4 t D3 V7 C9 T# x: C
fs2 20 1 0 1 0n #Integer, forced output8 u) B& |3 g7 B5 h6 n( X/ ~) V
# These formats used for 'Date' & 'Time'
2 I e+ q0 t. V1 @0 Z9 i+ e/ Rfs2 21 2.2 2.2lt #Decimal, force two leading & two trailing (time2): Q& C" [: K: I: P4 Q# N
fs2 22 2 0 2 0t #Integer, force trailing (hour)4 H \7 }8 m& _* L, G c: \0 }
fs2 23 0 2 0 2lt #Integer, force leading & trailing (min): d. f5 f# Q [3 ~& r( Y
# This format statement is used for sequence number output
S9 Y/ [+ s0 f" ^; Y, @. |# Number of places output is determined by value for "Increment Sequence Number" in CD; ?' N, I' {& R7 h3 v5 B( e1 X/ k
# Max depth to the right of the decimal point is set in the fs statement below' |' F& }0 o8 c A9 c
fs2 24 0^7 0^7 #Decimal, 7 place, omit decimal if integer value |
|
发表于 2012-4-9 21:38:45
发表于 2012-4-9 21:51:34
发表于 2012-4-9 23:07:40