|
|
马上注册，结识高手，享用更多资源，轻松玩转三维网社区。
您需要 登录 才可以下载或查看，没有帐号？注册
x
本帖最后由 lyd_2005 于 2015-10-23 13:54 编辑 * ]$ W; r G+ f
$ U8 }9 Z1 @+ a/ C1 g
! U5 \8 B0 Y! h W; | m4 e
8 c- k1 @# H+ o7 l k# p' `& o1.查找 ptap$ #Canned Tap Cycle. i' s2 L% v* V# h$ n" q) w
) e$ A4 E# q- u- m
& T% L' U8 x" ?" [ t' u1 t
到 pcom_movea 中间部分修改为
, I9 Z! T. a* s. q; W ptap$ #Canned Tap Cycle
) v: N' D. N5 q6 Q/ ]% ` pdrlcommonb7 U% I/ G3 F! U: L$ L5 a
if peck2$ = 0,. v( m: P: \) P
[
& J1 [4 a( p' W' x2 E1 }: H, E #RH/LH based on spindle direction
; y0 I* S' K$ a9 i g if rigid_tap, pbld, *sm29, *speed, e$ #Rigid Tapping$ w+ t( H% ?$ `6 w. e+ }
pcan1, pbld, *sgdrlref, *sgdrill, pdrlxy, pfzout, pcout, pindexdrl,+ q X4 D0 p9 h& l& A
prdrlout, [if peck1$, *peck1$], *feed, strcantext, e$. L8 M# w: B8 _# h3 D) p
]
3 j1 I0 p( v: m8 H9 a else,
% M' H/ ^. i7 G( F% Y5 j% w, \ [
; l% ]# o( H# s, K% G X0 N "M03",*speed, e$3 O5 K! |2 W& H% U _
"G94", e$/ S9 [6 l# m V1 j( v
if metvals, pitch = n_tap_thds$ # Tap pitch (mm per thread)
0 T/ F* m9 }1 L else, pitch = 1/n_tap_thds$ # Tap pitch (inches per thread)4 l% ^. b. u [1 B; X* _
pcan1, pbld, *sgdrlref, *sgdrill, pdrlxy, pfzout, pcout, pindexdrl,
0 q }0 A1 G9 G$ [; L1 ^" Q prdrlout, [if peck1$, *peck1$], *pitch, !feed, strcantext, e$% p; \: y+ r/ j- o0 a
]
% |0 P. b: x: _0 M& R/ @1 Z% i5 H! P pcom_movea
7 _2 P% F0 Z. b6 p- f' C, {2. [tap]
! S2 b! z/ Q, z$ H 1. "G84/G74 - Tap"
6 u# i/ G* Y5 s+ q 3. "") Z) \# l& R; I' I1 t6 v. }
7. "Peck"
* u9 E; q S9 C% F" b 8. 将 "" 修改为 "0为G95方式，1为G94" 要冒号（有两处）
: i, t% P# O" W* U7 h2 ` 9. "" A* r v( x' M+ M/ C b- j3 u
10. ""
2 M# Q3 ]3 r9 c% I 11. ""& y7 U9 Y2 C# Z# K3 D. |% P# f
3. pcanceldc$ #Cancel canned drill cycle/ R9 x$ ^* l/ ^/ B) C
result = newfs (three, zinc)5 u/ z: m$ H6 f G, b+ L
if drillref = 0, zabs = initht_a #Make the initht the modal Z value) k" J2 y w6 V% }/ R; \ K7 _; d
else, zabs = refht_a
( T4 A9 [7 O% a$ q# X2 G8 b9 ? prv_zia = zabs3 d9 A. z; n; T6 e; A8 S
!zabs
0 }5 t, t, l: H) V3 B" o# z" s ps_inc_calc( V6 I$ J* b- F0 `& O! Z4 ?5 o, o
prv_gcode$ = zero6 j" @: v& o0 U0 U w9 c; v. n
if cool_zmove = yes$ & (nextop$=1003 | (nextop$=1011 & t$<>abs(nexttool))), coolant$ = zero
4 y+ O) N8 y5 \3 U; z" p pcan0 S" _2 d+ B4 v/ h
if drillcyc$ <> 8, pcan1, pbld, "G80", scoolant, strcantext, e$5 w4 r4 \9 o* W4 n9 s' T- u% z
if peck2$ = 1,"G95", e$ 增加此行( q5 M9 l9 ~0 [1 u' z3 D4 W
#pbld, sgfeed, e$
4 k1 _6 M3 q3 b) F1 m4 s pcan2; U( \' Z$ x% f. T& ?
因本人不使用此功能，只是一个思路，以上G94，G95,自行调整。 R- [' a5 _ h H
' L9 `5 i( F6 v% n
& h# M4 }2 n! z7 q
& Y" ]- |7 Q8 g# X% Q$ G) h |
|
发表于 2015-10-23 12:14:04
楼主
