|
|
楼主 |
发表于 2007-2-10 23:56:58
|
显示全部楼层
来自： 中国江苏南通
我是这样做的，可不行．: [- u6 t2 }( n6 u' j6 X
运行后生成的几个视图不一样大，（虽然比例已设为一样），每个视图中显示不全整个零件，虽然加ＡＵＴＯ能显示出整个零件，可各个视图里的零件不一样大（长宽没有投影关系），
* a9 n2 O* c5 i( A8 z 而且运行好ＧＲＩＰ后只要手动一移运视图，就又变成都了没有auto前的样子．' [- H2 x! _) S& L& A
drawc/'ele',mmeter,210,297,iferr,mess:5 Z1 R: i; v3 Z& H8 F4 F
drawe/add,'top',40,200,iferr,term:
8 Z& D) M: T9 x4 ^/ r1 P: w; t. zdrawe/add,'front',40,50,iferr,term:( d) z# r, m5 w5 f' c
drawe/add,'right',150,200,iferr,term:
p) ~' ?* x6 ?8 Q' W- r* T1 Udrawv/'ele',na0 m+ [/ `( n! @2 V. d
drawe/'ele',dvstat,na(1),active) f5 M9 g" O- J: s
viewe/na(1),center,70,150,save5 U# ]% P. ?3 G
viewe/na(1),auto,save
o M) Q/ U/ p( r" p7 o: H& H3 ^! i/ bviewe/na(1),scale,0.2,dscale,0.3,save
1 B+ @& }% G, v/ ]viewe/na(1),auto,save5 Y8 z- G% U* M2 t$ D
drawe/'ele',dvstat,na(2),active
, G1 J c% P/ g! s( s- t4 m2 b) Uviewe/na(2),center,70,50,save
- j T3 |9 p0 R3 a+ k% y6 z! ~* Oviewe/na(2),auto,save6 h+ s1 S& B& b9 T4 l
viewe/na(2),scale,0.2,dscale,0.3,save, `- j% i+ `" m s9 U3 Y; [! N t
viewe/na(2),auto,save
0 @* j# d: Q- }drawe/'ele',dvstat,na(3),active
7 _6 U# X: R" {% \# a9 e. bviewe/na(3),center,210,50,save
3 p+ ?, J* i2 ?+ c# h J: c2 jviewe/na(3),auto,save
2 U% t# r8 V2 K& D( nviewe/na(3),scale,0.2,dscale,0.3,save
; A5 R$ g! Q, ~4 nviewe/na(3),auto,save& w/ V8 W$ L+ L4 a
# q# {% l$ R5 K
出个图都这么难搞定．不知大哥你的程序也是这样一个加图纸，加视图，改视图的过程？不太明白你上面这一贴的意思．+ x: ]& G x% e$ c
" V% t# R- K& T: N7 T& H
[ 本帖最后由 zgjshahxm 于 2007-2-11 00:16 编辑 ] |
|
发表于 2007-2-8 23:08:45
