2004一般会在编辑过工具栏后自动保存一次acad.mnr文件，下次启动时就会显示编辑后的工具栏；
: q0 ?# k8 C& S按下面打开菜单文件，保存一下；- P1 m6 e! p5 S& B
或者找到里面的对应工具栏项直接修改，再保存；
9 w; l! F& Q& D5 D' x2 |找到下面的代码段：
6 p6 ^9 O* g+ e7 S/ W( E8 `" _**TB_MODIFY5 m8 t- y: i2 M5 @
**修改. j3 S0 D# u- c H3 _7 H
ID_TbModify [_Toolbar("修改", _Left, _Show, 1, 0, 1)]
& h/ `7 W s/ n4 P ^9 _4 B1 \% fID_Erase [_Button("删除", "RCDATA_16_ERASE", "RCDATA_16_ERASE")]^C^C_erase
( _0 r0 n" |2 A5 D2 XID_Copy [_Button("复制对象", "RCDATA_16_COPYOB", "RCDATA_16_COPYOB")]$M=$(if,$(eq,$(substr,$(getvar,cmdnames),1,4),grip),_copy,^C^C_copy)
; W+ z" K9 ^" e& qID_Mirror [_Button("镜像", "RCDATA_16_MIRROR", "RCDATA_16_MIRROR")]$M=$(if,$(eq,$(substr,$(getvar,cmdnames),1,4),grip),_mirror,^C^C_mirror)
6 Y n, F: Q6 d8 E8 k, jID_Offset [_Button("偏移", "RCDATA_16_OFFSET", "RCDATA_16_OFFSET")]^C^C_offset
% U8 D' @6 w$ p$ c- T; vID_Array [_Button("阵列", "RCDATA_16_ARRREC", "RCDATA_16_ARRREC")]^C^C_array
a6 ?$ B' f/ t4 gID_Move [_Button("移动", "RCDATA_16_MOVE", "RCDATA_16_MOVE")]$M=$(if,$(eq,$(substr,$(getvar,cmdnames),1,4),grip),_move,^C^C_move) - g0 r3 W$ B; \
ID_Rotate [_Button("旋转", "RCDATA_16_ROTATE", "RCDATA_16_ROTATE")]$M=$(if,$(eq,$(substr,$(getvar,cmdnames),1,4),grip),_rotate,^C^C_rotate) 2 f! Y2 i) Q7 y% w( E
ID_Scale [_Button("缩放", "RCDATA_16_SCALE", "RCDATA_16_SCALE")]$M=$(if,$(eq,$(substr,$(getvar,cmdnames),1,4),grip),_scale,^C^C_scale)
- n+ f9 |8 }6 A |. qID_Stretch [_Button("拉伸", "RCDATA_16_STRETC", "RCDATA_16_STRETC")]$M=$(if,$(eq,$(substr,$(getvar,cmdnames),1,4),GRIP),_stretch,^C^C_stretch)
& \8 w; V; t0 V9 V( X6 [! U1 CID_Trim [_Button("修剪", "RCDATA_16_TRIM", "RCDATA_16_TRIM")]^C^C_trim 5 ^. c8 d8 \& V; t
ID_Extend [_Button("延伸", "RCDATA_16_EXTEND", "RCDATA_16_EXTEND")]^C^C_extend : q, N6 e3 L# B! b/ x- k+ s% c3 `
ID_BreakSele [_Button("打断于点", "RCDATA_16_BREAKATPT", "RCDATA_16_BREAKATPT")]^C^C_break \_f \@
0 g. A2 m: W, r7 jID_Break [_Button("打断", "RCDATA_16_BRE2PT", "RCDATA_16_BRE2PT")]^C^C_break 6 Q3 ~0 e" R. Q
ID_Chamfer [_Button("倒角", "RCDATA_16_CHAMFE", "RCDATA_16_CHAMFE")]^C^C_chamfer 3 R% m8 A! M3 [+ |* Y7 e
ID_Fillet [_Button("圆角", "RCDATA_16_FILLET", "RCDATA_16_FILLET")]^C^C_fillet 2 E0 {7 m+ j3 {" u) A3 Q
ID_Explode [_Button("分解", "RCDATA_16_EXPLOD", "RCDATA_16_EXPLOD")]^C^C_explode
8 F& [- d2 G5 {! L" u( r/ W9 tID_Hatchedit_0 [_Button("编辑图案填充", "RCDATA_16_HATEDI", "RCDATA_16_HATEDI")]^C^C_hatchedit （要增加的代码）- h8 w5 a3 F: ^" I8 b
$ R( P% P5 J+ I6 R6 f( U3 v, K: E然后卸载ACAD菜单文件，再加载ACAD.MNS菜单文件即可；+ ?4 m, A1 J6 d+ F, q0 o
) M2 p. F+ R/ z3 l; |
) y3 r1 o6 o4 |: n- V[ 本帖最后由 sealive_leafage 于 2008-6-4 15:56 编辑 ] |
发表于 2008-6-4 14:36:27
发表于 2008-6-4 15:38:44
发表于 2008-6-4 15:50:59
楼主