老大帮我呀。。。

dazhi518

模型输入以后，白色的系统坐标在电极的分中台上。建立用户坐标，用坐标器摆正，系统坐标就和用户坐标在一块了，可是我想让系统坐标在原位置上不动，只动用户坐标该如何编代码呀。。。

我是这样编的，请老大帮帮忙，该如何该呀。
0 y- d$ _. @3 f: |' ZPrivate Sub Command4_Click()
1 r" q+ b0 s/ l' nDim XMAX, XMIN, YMAX, YMIN, ZMAX As long
PowerMILL31.Connect
PowerMILL31.Execute ("Form BLOCK")
: C3 q0 m, C2 P2 ZPowerMILL31.Execute ("EDIT BLOCK ALL UNLOCK")
PowerMILL31.Execute ("EDIT BLOCK TOLERANCE 0.1")
PowerMILL31.Execute ("EDIT BLOCK RESETLIMIT 0.")
PowerMILL31.Execute ("EDIT BLOCK RESET")
PowerMILL31.Execute ("BLOCK ACCEPT")
ZMAX = PowerMILL31.ExecuteEx("PRINT FORMVALUE RoughBlock.LimitFrame.MaxZ")
XMAX = PowerMILL31.ExecuteEx("PRINT FORMVALUE RoughBlock.LimitFrame.MaxX")
$ m: K3 o$ I; k& w2 Q# V% ?XMIN = PowerMILL31.ExecuteEx("PRINT FORMVALUE RoughBlock.LimitFrame.MinX")
YMAX = PowerMILL31.ExecuteEx("PRINT FORMVALUE RoughBlock.LimitFrame.MaxY")
+ |- z4 E: ?" KYMIN = PowerMILL31.ExecuteEx("PRINT FORMVALUE RoughBlock.LimitFrame.MinY")
PowerMILL31.Execute ("TRANSFORM RESET TRANSFORM TYPE MOVE TRANSFORM MOVEX  " + CStr(-(XMAX - (XMAX - XMIN) / 2)))
PowerMILL31.Execute ("TRANSFORM MODEL ALL")
PowerMILL31.Execute ("TRANSFORM RESET TRANSFORM TYPE MOVE TRANSFORM MOVEY  " + CStr(-(YMAX - (YMAX - YMIN) / 2)))
PowerMILL31.Execute ("TRANSFORM MODEL ALL")
PowerMILL31.Execute ("TRANSFORM RESET TRANSFORM TYPE MOVE TRANSFORM MOVEZ   " + CStr(-ZMAX))
* P% H( i. M, I$ z2 BPowerMILL31.Execute ("TRANSFORM MODEL ALL")
3 |' g" ]( Q: [) b2 KPowerMILL31.Execute ("Delete BLOCK")
PowerMILL31.Disconnect

hh749

使用创建坐标指令来解决,

dazhi518

还是解决不了呀,,,老大.

hh749

pmill.StoreModel
: C6 L% \2 j- R. Wxmin = pmill.BlockSize(psXMin)
. I8 h1 D7 n+ ], c+ U+ pXMAX = pmill.BlockSize(psXMax)
+ \$ O3 D& q  M8 D' E- X% G4 VYMIN = pmill.BlockSize(psymin)
YMAX = pmill.BlockSize(psymax)
ZMIN = pmill.BlockSize(pszmin)
6 r  X4 H3 l1 |# w" c# Q  JZMAX = pmill.BlockSize(pszmax)
WKPLX = xmin + (XMAX - xmin) / 2
( P6 H9 d4 d3 ~: X$ t" K( @# kWKPLY = YMIN + (YMAX - YMIN) / 2
: j  U9 _! ?1 ]; j4 ]WKPLZ = ZMAX
& e! N$ s# |( B, spmill.Execute "CREATE WORKPLANE ;"
pmill.GetWorkplaneList WorkplaneList, ActiveWorkplane
NewWkpl = WorkplaneList(WorkplaneList.Count)
* \  k! |/ g! U- u& C7 C, ^pmill.Execute "MOVE WORKPLANE  '" & NewWkpl & "' X " & Format(WKPLX) & " Y " & Format(WKPLY) & " Z " & Format(WKPLZ)
3 Y: j- J% [7 [! S* S, O: D' Rpml_send ("ACTIVATE Workplane " & "'" & NewWkpl & "'")
" n( U+ P! r7 @  g  P: ipml_send ("TRANSFORM RESET TRANSFORM TYPE WORLD TRANSFORM MODEL ALL SELECTED")
pml_send ("DELETE Workplane " & "'" & NewWkpl & "'")
2 J4 M3 f/ h: [; b
之前给ＪＩＭ写的一个外挂的代码，这部分是建立坐标的代码，你可以参照下

6 v3 p! C. G% I0 S- K1 l[ 本帖最后由 hh749 于 2009-4-16 21:41 编辑 ]

dazhi518

太谢谢老大了，感激不尽呀。。

dazhi518

老大,能不能发个完整一点的呀，，我对宏和VB不是非常的了解呀。。。。loveshenzhichen888@126.com本人邮箱。谢谢。

hh749

自己写,编程就是要靠自己的努力去完成,老用别人的自己就没得进步,方法我已经说了!