|
|
楼主 |
发表于 2011-7-28 05:20:31
|
显示全部楼层
来自： 加拿大
: K% W3 V1 `8 ]9 V% b; X6 P' S( I9 S1 U4 H8 [ t' w I% D
# G N; t8 K2 ` e# x K5 ^# A
全世界都知道，但说说方法吧 1 z4 H' ~/ Y, R' T# f$ O
- U8 [7 x* a- }) N, D$ A我现在用工单的方法输出， 但这方法读不出没有用到程序上的刀夹。4 m: i3 g# D5 ]4 v0 o
/ |% N, F; ]1 ]0 ^5 u! ?
令一方法是读进刀具数据库再输出， 但效率不好。
4 w% x7 _ E" m; r% h- e" z2 {$ z. q: r
ype,Name,Number,Diameter,Length,Tip Radius,Chamfer Angle,Chamfer Length,X Offset,Y Offset
+ @, V' g% X# f3 O/ g6 C. M, g8 W% o# k* K5 P4 B, V. q# J- A
Ball,1,0,10.0,50.0,0.0,0.0,0.0,0.0,0.0
6 W4 G4 F0 ~$ F$ A. \Holder********************************************8 d b9 y2 \. R4 w8 U; ?. {
0.000000000000000 0.000000000000000 0.000000000000000
0 J" K* s1 m( k3 e* q7 Z12.800000000000001 0.000000000000000 0.0000000000000008 O# i9 K. n) @! `( c
16.070000000000000 0.000000000000000 17.0500000000000012 d4 c, X' u8 i% s4 u! w
16.070000000000000 0.000000000000000 41.500000000000000
3 F0 R* P7 G1 r9 q25.170000000000002 0.000000000000000 46.730000000000004
* a5 X0 ?0 V$ N% Z6 i25.170000000000002 0.000000000000000 60.860000000000007
' q3 x' k7 n& i+ \( b. F% D0 t) ]* d31.350000000000001 0.000000000000000 60.860000000000007
& M: m7 g& X. F. v* J4 b31.350000000000001 0.000000000000000 86.830000000000013
r$ b- y0 c3 J3 x* x. ]$ V5 q7 `' a& w* k( ]
Ball,2,0,10.888,54.44,0.0,0.0,0.0,0.0,0.0
: ?# g; W6 i0 kShank--------------------------------------------- w q7 T1 y' M) j
0.000000000000000 0.000000000000000 0.000000000000000
1 D6 X" @ M0 n3 L/ a; ]0.000000000000000 0.000000000000000 54.439999999999998* X* C7 g% |- H
8.166000000000000 0.000000000000000 54.439999999999998
3 y. ?' _2 B* f8.166000000000000 0.000000000000000 108.880000000000000" v! Z7 o4 |8 n
, z" C# [6 R I, e7 X# f
Ball,2_1,0,10.888,54.44,0.0,0.0,0.0,0.0,0.0
6 g$ {- G/ v& j F/ ?& `. R" ^Shank--------------------------------------------
& s/ i1 y% i5 u% A! r( I# \0.000000000000000 0.000000000000000 0.000000000000000
- k6 H2 m) p6 a- k0.000000000000000 0.000000000000000 54.4399999999999987 \4 t% q! K. X" k8 N
8.166000000000000 0.000000000000000 54.439999999999998
) ?( W/ S" l% ~8 b9 V8.166000000000000 0.000000000000000 108.880000000000000' O4 D3 b' L% u! k9 J8 l0 N7 a
' }6 o+ T, s$ I% {* RTap,3,0,10.888,54.44,0.0,0.0,0.0,0.0,0.03 P& W" j, H& r
Shank--------------------------------------------
) j$ W! N1 N5 A16.332 16.332 54.44 0 |
|
发表于 2011-7-19 21:46:53
