|
|
楼主 |
发表于 2015-11-7 22:00:18
|
显示全部楼层
来自： 中国广东广州
多谢各位现在不用备刀，西门子的备刀我也不懂，我这个程式钻孔是没有问题的，% i4 c* n9 ~. y
%_N_ 01 _MPF0 o8 `0 u2 y# ?6 N' y+ t% W9 F4 s1 O
;$PATH=/_N_WKS_DIR/_N_WD_WPD
! H& D9 m) ` k, o* W;(***05-11-15*** ***16:37***)
1 |+ t! n( ?+ w h9 N;(T1 30 BULL-NOSED ENDMILL ), h5 N! x9 L4 c2 h! f
;(T2 17 BULL-NOSED ENDMILL )
0 o$ |1 B0 v9 u: L;(T3 26 BULL-NOSED ENDMILL ), I+ A8 ]1 _+ b/ r O
;(T5 10 FLAT ENDMILL )
* c7 R9 d% q/ m. ~% ^;(T6 10 FLAT ENDMILL )
/ W* o9 b9 ~! W, [, h u. l;(T106 CHAMFER MILL )5 s6 T% p# J* @) g' p g
;(T7 STANDARD DRILL - 3 )3 r! g* M7 F! T
;(T9 STANDARD DRILL - 4.3 )8 Y& n8 y" h ~0 h- {
;(T8 STANDARD DRILL - 3.3 )
6 _0 ~2 s) H/ x/ o) @, R;(OVERALL MAX - Z20.)' Q7 @7 j4 }) U1 H4 |
;(OVERALL MIN - Z-22.)
- p) a0 h O, {0 pG64 SOFT9 P6 [; v. U' Z2 @' I: I: Q5 N
G542 ?' [. b7 x: P: a! R" A9 O
T1
; [9 N( A( G8 o2 }4 YM06
! M7 J* r/ I; |) K" @ X;( 30 BULL-NOSED ENDMILL ); T9 Q: c0 \& Z9 m3 o' K5 c1 L
G00 G90 X68. Y-39.344 S2500 M03
+ f- p# G! \* K6 b2 X3 mG01 Z20. F5000
3 I% v4 A; X: @. G. u8 LM08
3 i! y1 e# V! v% q;(MAX - Z20.)
- P! `) s, j) T' ];(MIN - Z-5.1)
9 A) J- y, @/ f, A9 e/ Z) WZ2., i7 x0 U* A0 e4 w
G01 Z-.425 F3000.! t5 S$ O( I/ @# ~3 F" p8 x1 K
Y-8.656 F4000., G" T1 S! _( C+ V3 c, O0 l0 Z
X-68.7 N0 \5 _) H5 v
Y-39.344# B; w& s* X( O F% [7 U6 _
Z-.85 F3000.
3 }0 r' i' D! ^5 OY-8.656 F4000.( _1 ?9 k/ G3 t" L: z7 K4 a: `
X68.
/ y% e5 q% m9 S0 I8 U4 d$ O W/ bY-39.344/ _3 a8 \& \+ n o2 f6 N4 a
Z-1.275 F3000.
- Z9 w6 `# p1 gY-8.656 F4000.7 x, E9 t1 @! V
X-68.
2 U4 ] N$ V# y0 R$ eY-39.344
6 ~6 X; j! T- ]: d5 d% c ?Z-1.7 F3000.
1 c# ^; }! E' U% r dY-8.656 F4000.
- Y+ J' T: A5 h5 n5 b7 {+ ?X68. |
|
发表于 2015-11-7 08:48:09
