2004一般会在编辑过工具栏后自动保存一次acad.mnr文件，下次启动时就会显示编辑后的工具栏；
3 s; m. N+ o9 ?* j按下面打开菜单文件，保存一下；
4 V3 |+ t( s$ H3 i2 ~或者找到里面的对应工具栏项直接修改，再保存；
5 ^3 @% |7 L4 C找到下面的代码段：/ t6 P2 C- N& u1 j5 F9 W
**TB_MODIFY, D. m2 Y( u8 A# F! g
**修改
7 L+ [: v+ ]6 i: N, @; |+ sID_TbModify [_Toolbar("修改", _Left, _Show, 1, 0, 1)]9 z1 X8 d9 T# K) i1 t! `, D$ M
ID_Erase [_Button("删除", "RCDATA_16_ERASE", "RCDATA_16_ERASE")]^C^C_erase ; X3 d' [/ U8 F$ a0 n
ID_Copy [_Button("复制对象", "RCDATA_16_COPYOB", "RCDATA_16_COPYOB")]$M=$(if,$(eq,$(substr,$(getvar,cmdnames),1,4),grip),_copy,^C^C_copy) 7 Y2 |: m) _8 Q; q3 o4 o* i5 i ]
ID_Mirror [_Button("镜像", "RCDATA_16_MIRROR", "RCDATA_16_MIRROR")]$M=$(if,$(eq,$(substr,$(getvar,cmdnames),1,4),grip),_mirror,^C^C_mirror)
! K5 D. {9 y/ e) rID_Offset [_Button("偏移", "RCDATA_16_OFFSET", "RCDATA_16_OFFSET")]^C^C_offset " D' M: }; X0 {' s4 p. t
ID_Array [_Button("阵列", "RCDATA_16_ARRREC", "RCDATA_16_ARRREC")]^C^C_array
4 O8 ?+ g8 ^- p2 H2 dID_Move [_Button("移动", "RCDATA_16_MOVE", "RCDATA_16_MOVE")]$M=$(if,$(eq,$(substr,$(getvar,cmdnames),1,4),grip),_move,^C^C_move) , {1 K+ ]7 s) F
ID_Rotate [_Button("旋转", "RCDATA_16_ROTATE", "RCDATA_16_ROTATE")]$M=$(if,$(eq,$(substr,$(getvar,cmdnames),1,4),grip),_rotate,^C^C_rotate) + I# \ C+ d! n6 x2 l0 A
ID_Scale [_Button("缩放", "RCDATA_16_SCALE", "RCDATA_16_SCALE")]$M=$(if,$(eq,$(substr,$(getvar,cmdnames),1,4),grip),_scale,^C^C_scale) 9 G0 Y# [& l( u! F
ID_Stretch [_Button("拉伸", "RCDATA_16_STRETC", "RCDATA_16_STRETC")]$M=$(if,$(eq,$(substr,$(getvar,cmdnames),1,4),GRIP),_stretch,^C^C_stretch) 5 C$ W2 [/ ]! M$ F; a
ID_Trim [_Button("修剪", "RCDATA_16_TRIM", "RCDATA_16_TRIM")]^C^C_trim
9 t% ^2 h# Q6 DID_Extend [_Button("延伸", "RCDATA_16_EXTEND", "RCDATA_16_EXTEND")]^C^C_extend # B/ [) G& R& v! ?/ p' W( }0 @
ID_BreakSele [_Button("打断于点", "RCDATA_16_BREAKATPT", "RCDATA_16_BREAKATPT")]^C^C_break \_f \@ / h6 f- u+ v, ~3 l9 R" j
ID_Break [_Button("打断", "RCDATA_16_BRE2PT", "RCDATA_16_BRE2PT")]^C^C_break 5 u U. s$ _( h& F. D
ID_Chamfer [_Button("倒角", "RCDATA_16_CHAMFE", "RCDATA_16_CHAMFE")]^C^C_chamfer ) ]) z. A% {* m/ X7 e
ID_Fillet [_Button("圆角", "RCDATA_16_FILLET", "RCDATA_16_FILLET")]^C^C_fillet
/ N) ^% k% M- u/ y9 h" w/ R1 L& rID_Explode [_Button("分解", "RCDATA_16_EXPLOD", "RCDATA_16_EXPLOD")]^C^C_explode
) f' f( k, v$ Y6 z/ ~& g" \ID_Hatchedit_0 [_Button("编辑图案填充", "RCDATA_16_HATEDI", "RCDATA_16_HATEDI")]^C^C_hatchedit （要增加的代码）. N7 M* d1 o$ W: c3 ]
# L* i# X2 T; @2 J* |' V9 U5 R然后卸载ACAD菜单文件，再加载ACAD.MNS菜单文件即可；
+ A9 h7 `# A0 A* q7 }, J8 k. }+ M3 V2 C0 h z7 _$ T
6 B/ ]) w( j" z, d9 r" R: Q
[ 本帖最后由 sealive_leafage 于 2008-6-4 15:56 编辑 ] |
发表于 2008-6-4 14:36:27
发表于 2008-6-4 15:38:44
发表于 2008-6-4 15:50:59
楼主