2 I) e5 H/ y3 C VSorry, You've got a bad luck 4 y9 o ^* B3 d1 |; q Win XPSP3 has a bag with reading intermediate toolpath results file in HSM 2.3.3.6892 .. So it can not build a toolpaths...' m1 o0 O0 B: E6 D# Q0 O
* |* ~4 c* ~1 A4 v6 x
[ 本帖最后由 solid_user 于 2008-9-16 05:28 编辑 ]
+ n' B$ b: F) h, w* J5 JI don't know.. If you have got a newer than HSM 2.3.3.6892 Installation for Mc9.1 I can try to make a crack. Maybe it will be work under Windows XP XP35 I L* T" H0 m( Y
- V5 r( y5 @ T; z& EBTW HSM 3.0.31 for MC X-X3 is already released om cimco-hsm.com : o( X+ N! f$ e7 E- w; W* E 7 ]# @ y$ A9 I1 Z+ q[ 本帖最后由 solid_user 于 2008-9-16 05:49 编辑 ]
error: failed to read from kernel stream (please try to repair the installation)) D% F: T7 ]' ]
error: toolpath generation failed 7 } _0 u% x; Z2 d1 L4 v' b2 C! W& q# w P0 } \6 r4 @
I think I have to change the system
原帖由 joks 于 2008-9-16 06:11 发表 http://www.3dportal.cn/discuz/images/common/back.gif 7 R& b. ]$ ~0 W9 S1 E# ]1 K0 Nerror: failed to read from kernel stream (please try to repair the installation), y U! o5 S/ V* _7 T
error: toolpath generation failed & e$ C$ K: }1 |" ]( }6 k6 `
T' M5 a4 o1 J
I think I have to change the system
9 R( w2 i* c1 e( r+ [
That's bug of Win XP SP3 I said... 5 f* [' B( N7 ^% ]& w3 R/ eIn Win XP SP2 all works and you will not get that message : M0 k3 B; N3 R1 [ ~( X1 x. ~5 \" R X! B
[ 本帖最后由 solid_user 于 2008-9-16 06:37 编辑 ]
P" W, B9 L. @
I use different OS's on different computers..' g" j3 p) ?- K1 X, C+ T0 M
As for HSM 3.x.x it's good but it can not be run under MC 9.1... I think you need HSM not only for MC X-X3 but for MC 9.1 too.. Isn't it?# ~8 V9 ]) E+ _ p! W4 r4 E
2 j/ A! R6 d: G' M- a
BTW MoldPlus v10 SP0 for Mastercam X3 is already released on mastercam.fi & d. X7 V Z: C* R4 V' c/ [
I use different OS's on different computers.. = Oh!; r+ A6 ^' s; t
+ D0 W& F3 Z/ p/ ^0 C2 j/ L8 uAs for HSM 3.x.x it's but it can not be run under MC 9.1... I think you need HSM not only for MC X-X3 but for MC 9.1 too.. Isn't it? = Yes! I started learning is the most Mastercam, I like mastercam!4 V& E" v5 L1 g8 P
; }/ U: D1 x8 u8 bBTW MoldPlus v10 SP0 for Mastercam X3 is already released on mastercam.fi = Moldplus_10_SP0_for_X3 can use it without Crack ?
error: failed to read from kernel stream (please try to repair the installation), _! |, u3 b- h# e+ m
error: toolpath generation failed + r- u6 `: z" `0 T- }* R! q+ v
WORK IN SP2
error: failed to read from kernel stream (please try to repair the installation)2 I3 O% i% m- K3 D! H
error: toolpath generation failed ( b% g3 l# o5 _/ O- n, L2 [' G
WORK IN SP2
原帖由 ryanhe2008 于 2008-9-17 10:56 发表 http://www.3dportal.cn/discuz/images/common/back.gif$ `) Y1 n% j- K( Q
error: failed to read from kernel stream (please try to repair the installation) % Y/ ^# Y/ M8 _% d5 Uerror: toolpath generation failed . |: j8 J( B6 Z2 E# }
WORK IN SP2
# g( u$ Q. e1 v, ]6 f
I suppose that you have install some of Windows XP2 Update wich couse this bug.. [( ]4 x3 l+ f' L- }6 }. G1 S
In any case it's bug of Windows..
发表于 2008-9-16 03:48:05
Sofa! Thank you very much
0 w# K2 x8 P6 K3 _
楼主
4 y9 o ^* B3 d1 |; q
& d. X7 V Z: C* R4 V' c/ [
6 E' x% s, B; E+ x
Oh!; r+ A6 ^' s; t
Yes! I started learning is the most Mastercam, I like mastercam!4 V& E" v5 L1 g8 P
Moldplus_10_SP0_for_X3 can use it without Crack ?