老大帮我呀。。。

dazhi518

模型输入以后，白色的系统坐标在电极的分中台上。建立用户坐标，用坐标器摆正，系统坐标就和用户坐标在一块了，可是我想让系统坐标在原位置上不动，只动用户坐标该如何编代码呀。。。
7 Q" B1 G3 }2 k  d# H
) S5 r( Y4 q! b  n我是这样编的，请老大帮帮忙，该如何该呀。
Private Sub Command4_Click()
Dim XMAX, XMIN, YMAX, YMIN, ZMAX As long
PowerMILL31.Connect
PowerMILL31.Execute ("Form BLOCK")
PowerMILL31.Execute ("EDIT BLOCK ALL UNLOCK")
( Q$ P* E  F; C7 L7 d1 [+ nPowerMILL31.Execute ("EDIT BLOCK TOLERANCE 0.1")
3 I9 [/ J+ M. ~1 a; r3 ?PowerMILL31.Execute ("EDIT BLOCK RESETLIMIT 0.")
, k1 @# _3 W9 i) K6 j8 \3 F# ?PowerMILL31.Execute ("EDIT BLOCK RESET")
PowerMILL31.Execute ("BLOCK ACCEPT")
ZMAX = PowerMILL31.ExecuteEx("PRINT FORMVALUE RoughBlock.LimitFrame.MaxZ")
XMAX = PowerMILL31.ExecuteEx("PRINT FORMVALUE RoughBlock.LimitFrame.MaxX")
# A  L4 j- X- |, K* f# `3 PXMIN = PowerMILL31.ExecuteEx("PRINT FORMVALUE RoughBlock.LimitFrame.MinX")
% r% i; t7 v4 h; @; X$ m! U5 CYMAX = PowerMILL31.ExecuteEx("PRINT FORMVALUE RoughBlock.LimitFrame.MaxY")
YMIN = PowerMILL31.ExecuteEx("PRINT FORMVALUE RoughBlock.LimitFrame.MinY")
PowerMILL31.Execute ("TRANSFORM RESET TRANSFORM TYPE MOVE TRANSFORM MOVEX  " + CStr(-(XMAX - (XMAX - XMIN) / 2)))
: }) j/ b; Z" I6 {8 M: Q' M7 S6 w+ hPowerMILL31.Execute ("TRANSFORM MODEL ALL")
PowerMILL31.Execute ("TRANSFORM RESET TRANSFORM TYPE MOVE TRANSFORM MOVEY  " + CStr(-(YMAX - (YMAX - YMIN) / 2)))
  w% ]' _" N, C3 H" IPowerMILL31.Execute ("TRANSFORM MODEL ALL")
PowerMILL31.Execute ("TRANSFORM RESET TRANSFORM TYPE MOVE TRANSFORM MOVEZ   " + CStr(-ZMAX))
PowerMILL31.Execute ("TRANSFORM MODEL ALL")
! m3 K. z7 J* {7 J6 j- {0 YPowerMILL31.Execute ("Delete BLOCK")
PowerMILL31.Disconnect

hh749

使用创建坐标指令来解决,

dazhi518

还是解决不了呀,,,老大.

hh749

pmill.StoreModel
8 D* Q8 F& d5 B. q( a/ m1 O0 Jxmin = pmill.BlockSize(psXMin)
XMAX = pmill.BlockSize(psXMax)
YMIN = pmill.BlockSize(psymin)
: W* g* a4 h- d3 GYMAX = pmill.BlockSize(psymax)
ZMIN = pmill.BlockSize(pszmin)
( _( _5 w7 c- `/ o" [ZMAX = pmill.BlockSize(pszmax)
2 J  Q: ]( `0 L- ]- x( GWKPLX = xmin + (XMAX - xmin) / 2
1 M: `0 ]5 n  nWKPLY = YMIN + (YMAX - YMIN) / 2
WKPLZ = ZMAX
* \2 i% s7 z3 _3 opmill.Execute "CREATE WORKPLANE ;"
- Y, V, A- d5 M7 O7 |4 z* O, ypmill.GetWorkplaneList WorkplaneList, ActiveWorkplane
NewWkpl = WorkplaneList(WorkplaneList.Count)
, F/ T; w, C) n4 I! @pmill.Execute "MOVE WORKPLANE  '" & NewWkpl & "' X " & Format(WKPLX) & " Y " & Format(WKPLY) & " Z " & Format(WKPLZ)
pml_send ("ACTIVATE Workplane " & "'" & NewWkpl & "'")
& s: i. H' w" K/ Z) e, j5 Mpml_send ("TRANSFORM RESET TRANSFORM TYPE WORLD TRANSFORM MODEL ALL SELECTED")
pml_send ("DELETE Workplane " & "'" & NewWkpl & "'")

) d7 ^( ^8 ?* O5 n之前给ＪＩＭ写的一个外挂的代码，这部分是建立坐标的代码，你可以参照下

, \1 s; ]( F1 L: x% v5 s[ 本帖最后由 hh749 于 2009-4-16 21:41 编辑 ]

dazhi518

太谢谢老大了，感激不尽呀。。

dazhi518

老大,能不能发个完整一点的呀，，我对宏和VB不是非常的了解呀。。。。loveshenzhichen888@126.com本人邮箱。谢谢。

hh749

自己写,编程就是要靠自己的努力去完成,老用别人的自己就没得进步,方法我已经说了!