|
|
发表于 2009-11-8 00:22:47
|
显示全部楼层
来自： 中国浙江杭州
很简单的，使用一般的外形加工，参数中选第四轴即可4 Q' y1 D3 w# _6 L
%$ ^6 \+ M' U) f; B
O0000(1)4 n4 g/ ^% s/ ?, _
G213 e& H5 J4 O* a- S; G( q! R& ?
G0 G17 G40 G49 G80 G90: J; D% _9 N$ A' E7 W
T2 M63 G' [$ g% e; f# L( q8 j# e
G0 G90 G54 X-6.976 Y0. A-106.689 S5000 M3+ t# h" |- l+ t8 {. X* \. V* a
G43 H2 Z79.5
: t: k( P5 O. O# cZ39.5# t9 I' K7 J! S. f9 d3 A
G1 Z29.5 F50.( h6 g2 g6 r* n7 j# \; I
X-7.772 A-105.513 F1000.
" Y I0 w; c( M; x+ {X-7.929 A-105.278+ |) d4 [. ]0 B( r
X-8.084 A-105.038; X: G! V' B2 t/ B* y
X-8.237 A-104.7925 f. d$ `1 R& ^
X-8.388 A-104.5439 S, W4 O7 A6 R+ i5 j+ q0 ?( X1 T9 D
X-8.537 A-104.2882 W. [0 e8 p, D5 `+ u( Y; F4 R
X-8.684 A-104.0296 Q" x/ i( U& \. y& y: t Z
X-8.828 A-103.766* I; k0 F9 l1 Z
X-8.971 A-103.498$ A# F7 @( I( M8 C7 V
X-9.111 A-103.225
7 z' A! H2 U. `X-9.249 A-102.949
9 l5 X" u8 o5 d: T' f/ GX-9.385 A-102.668
S4 |( U5 m( c" m' \+ KX-9.934 A-101.513 F1426.4! p5 r( m6 L/ e* M% N
X-10.341 A-100.469 F1548.7; a3 e8 f( ?8 @
X-10.554 A-99.81 F1644.5
: e+ j; B% m: P% ^& rX-10.748 A-99.105 F1712.1- ]9 y" k' }* A: T" {. w$ O. ^
X-10.914 A-98.385 F1772.6 \1 k5 k$ V6 O) O- m2 r
X-11.049 A-97.663 F1825.2
% y* \4 q: W; L- F& ?2 Y1 \X-11.172 A-96.808 F1870.16 v5 {; w$ J: b" ]. }
X-11.26 A-95.935 F1905.8
8 f+ A7 T0 n [. [X-11.313 A-95.04 F1929.3. @: ?) x0 ~$ Y1 b2 H4 l
X-11.333 A-94.025 F1940.87 A: T& E2 }! }3 Z7 ~3 T0 L1 e
A-92.131
$ n5 p' X3 \$ u4 FA-90.157
9 ~' V9 j$ z& M; x1 m, @A-89.999, t1 r# V; X8 p9 D
A-88.025, @" f! n" Q; N" H
A-86.05
5 V& W$ [) a0 ]( N. p* V1 hA-86.025 |
-
|
